Fit verdict: MAXTRAX MKII Fit for vehicle storage depends on a long footprint and the height of the nested pair. The manufacturer lists each board at 1150 × 330 × 85 mm and a stacked pair at 95 mm high. That compact nesting figure does not include your storage bag, mounting hardware, or space needed to lift the boards out.

This guide uses published specifications and planning calculations, not a firsthand product test. Examples are hypothetical.
Dimensions and conditions
| Measurement | Published specification |
|---|---|
| One board, length × width × height | 1150 × 330 × 85 mm |
| Nested pair height | 95 mm |
| One board weight | 3.4 kg |
| Pair weight, before accessories | 6.8 kg |
1. Use MKII dimensions rather than family names
Write the exact model into your MAXTRAX MKII Fit plan. MAXTRAX also sells other board families, and their dimensions should not be substituted. Check whether you are storing one board, one nested pair, or a larger stack. The 85 mm individual height and 95 mm pair height are different measurements, so doubling the single-board height would overstate a properly nested pair. Conversely, treating a pair as one board understates its height.
2. Measure the full usable length
A storage drawer advertised as 1200 mm long may have a shorter interior after the front, rear panel, and hardware are accounted for. Measure the usable opening and the interior separately. For a cargo-floor arrangement, check seatback slope and hatch trim at the actual board height. The product length must fit through the opening as well as inside the compartment. A diagonal arrangement needs room for the full 330 mm width, not just the end-to-end diagonal line.
3. Test nesting with the accessories installed
For MAXTRAX MKII Fit under a cargo shelf, begin with the 95 mm pair figure, then measure your actual packed assembly. A carry bag, accumulated material, straps, or hardware can change its envelope. Do not assign a guessed allowance to every setup. Put the exact arrangement together and measure its highest point. The objective is a repeatable packing method, not a lid that closes only when someone presses hard on it.
4. Keep extraction possible when the vehicle is loaded
Think through which items must move before the boards become reachable. If they sit below the entire camping load, dimensional fit may come at the cost of awkward access. Mock up the loading order with a full-size cardboard footprint before buying a drawer or shelf. MAXTRAX MKII Fit should include a path for hands and the initial lifting motion. A compartment that exactly matches the board outline may still prevent a practical grip.
5. Evaluate mounting and transport separately
If you intend to mount the boards outside the vehicle, follow the board mounting system, rack, and vehicle instructions. Matching the board footprint to a roof platform does not establish compatible hole spacing, suitable fasteners, or permitted loading. Include the boards and all brackets in the load calculation. Inside the vehicle, use an appropriate secured arrangement rather than leaving the pair loose. This guide checks storage geometry; it does not certify a custom mount or recovery technique.
MAXTRAX MKII Fit: a worked example
Consider a hypothetical drawer with a clear interior 1180 mm long, 350 mm wide, and 100 mm high. A bare nested pair has geometric differences of 30 mm in length, 20 mm in width, and only 5 mm in height. If the drawer opening is 92 mm high, the 95 mm pair fails straight entry despite the taller interior. If a bag brings the measured packed height to 104 mm, it also fails the interior height check. MAXTRAX MKII Fit in this example is therefore unresolved until the opening and complete packed assembly both pass; the bare product numbers alone are insufficient.
Before you decide
- Confirm the MKII model and number of boards.
- Measure the nested pair with its real bag or accessories.
- Check both the opening and usable interior dimensions.
- Test removal with the surrounding cargo in place.
- Follow the relevant mounting and load-restraint instructions.
FAQ
Is a pair 170 mm tall?
The official product page gives 95 mm for a nested pair. MAXTRAX MKII Fit calculations should use that figure only when the boards are nested as intended, without assuming accessories are included.
Can I use the boards as a loading ramp?
Do not infer ramp suitability from storage dimensions. The manufacturer FAQ says MAXTRAX are not meant to be used as a bridge or ramp. Follow its instructions for the intended recovery use.
Does an 1150 mm compartment guarantee a fit?
No. An equal nominal length leaves no demonstrated room for manufacturing variation, obstructions, or insertion. Measure the actual compartment and assembly, and test the loading route without forcing the boards.
Related fit guides
Cargo height below a tonneau cover and Roof basket and crossbar mounting checks.
Official sources
Specifications checked November 5, 2026. Confirm the exact model and current instructions before purchase or installation.



