Will an M.2 SSD with a Heatsink Fit Your PS5 Expansion Slot?

Original explanatory cross-section diagram of a PS5 M.2 SSD assembly, identifying separate above-board, below-board and total-height limits; not an installation photograph.

Result — Conditional. The complete SSD and cooling assembly must satisfy Sony’s expansion-slot dimensions, including separate limits above and below the circuit board. A bare drive advertised as 2280 does not establish the fit of an aftermarket heatsink.

Original explanatory cross-section diagram of a PS5 M.2 SSD assembly, identifying separate above-board, below-board and total-height limits; not an installation photograph.
Original Will It Fit Here explanatory diagram, not to scale. It illustrates the measurements discussed below; it is not a product photograph or a firsthand fit test.

Dimensions: measure the finished assembly

Sony’s PS5 installation guide specifies a PCIe Gen4 x4 M.2 NVMe, Key M drive and requires an effective cooling structure. Its size table allows an assembled width up to 25 mm and total thickness up to 11.25 mm, with no more than 8.0 mm above the board and 2.45 mm below it. Supported lengths are 30, 42, 60, 80 and 110 mm. Check the exact current PS5 instructions before choosing a drive.

Fit question Reference or action
Bare format 2230, 2242, 2260, 2280 or 22110
Complete assembly width 25 mm maximum, including cooling structure
Above / below board 8.0 mm / 2.45 mm maximum respectively
Complete thickness 11.25 mm maximum
Other requirements Check interface, capacity, cooling and current system software

A total-height pass can conceal a local failure

Suppose an imaginary assembly extends 9 mm above its board and 1 mm below. Its 10 mm total is below 11.25 mm, but the upper portion still exceeds 8 mm. This is a no-fit comparison against the stated upper limit. Adding the two clearances together does not let you transfer unused space from one side to the other.

Request a dimensioned assembly drawing from the SSD or heatsink maker. Identify the circuit-board reference plane and whether the drawing includes the thermal pads, fastening clips and lower plate. A headline “10 mm heatsink” can describe a component rather than the installed package. Do not assume two separately acceptable parts will create an acceptable combined envelope.

Read the label before reading the ruler

A common 2280 format describes a nominal 22 mm wide, 80 mm long board. It does not identify the storage interface or the cooling package. Sony does not support M.2 SATA drives for this expansion slot. Its guide lists 250 GB–8 TB capacity and recommends sequential read speed of 5,500 MB/s or faster. Those requirements are independent of the physical-size check.

Write down the complete SSD model and the heatsink model as a pair. If buying a preassembled version, use its finished dimensions rather than dimensions from the bare-drive version in the same product family. For a separate cooling kit, confirm that the SSD maker permits that assembly and follow the kit’s pad arrangement.

Plan installation and subsequent access

Use Sony’s guide for your console group, update the system as instructed, and follow its power-disconnection and handling procedure. The spacer and fastening position must match the drive length. Leave room on your work surface to remove and replace the console panels normally rather than attempting the work inside a tight cabinet.

Complete the installation with the expansion-slot cover and console covers fitted as directed. A cover that meets resistance is a reason to recheck the assembly, not evidence that tightening it will create clearance. Keep the drive’s packaging and model information so that a later storage or cooling problem can be checked against the exact installed combination.

Before you decide

  • Record the SSD, cooling-kit and PS5 model group.
  • Check the complete width, length and both board-side heights.
  • Confirm the supported interface, capacity, cooling and software requirements.
  • Follow Sony’s fitting procedure and restore the required covers.

FAQ

Does 2280 mean a heatsink will fit?

No. It describes the nominal board format; the finished cooling assembly needs its own dimensioned check.

Can spare space below compensate for excess height above?

No. The above-board and below-board limits apply separately, alongside total thickness.

Official sources and scope

Specifications and guidance checked on 22 October 2026. The named model and region control; follow the matching current instructions for your product. Worked examples are identified as hypothetical.

Related fit guide