Yakima OverNOut Fit: 5 Essential Awning-Space Checks

Original Yakima OverNOut explanatory diagram showing separate crossbar spread and deployed canopy area, with extra campsite space for supports.

Result — Conditional. The Yakima OverNOut SM page specifies a minimum 24-inch crossbar spread and a deployed 54 × 78-inch canopy. A rack that accepts the clamps still needs room for the packed case, neighbouring equipment, vehicle doors and the awning’s fully supported campsite arrangement.

Original Yakima OverNOut explanatory diagram showing separate crossbar spread and deployed canopy area, with extra campsite space for supports.
Original Will It Fit Here explanatory diagram, not to scale. This is a measurement illustration, not a product photograph or a firsthand fit test.

1. Match the Yakima OverNOut size and label

This guide addresses the US SM listing, SKU 8007444, described as the 4.5-foot awning. The product family also has larger options. Do not apply the small canopy footprint to a larger case merely because the mounting hardware looks similar. Record the model label, size selection and current manual together. The name printed on a used awning bag may also differ from the current catalogue, so verify the actual product before using this comparison.

2. Dimensions: measure crossbar spread correctly

The stated minimum spread is 24 inches, equivalent to 609.6 mm. Check the mounting reference points in the manual rather than measuring an arbitrary visible gap between bar edges. A hypothetical 580 mm spread falls 29.6 mm short of that minimum. A longer canopy does not compensate for insufficient support. Move adjustable bars only within the vehicle and rack manufacturer’s permitted positions; fixed mounting locations are not an invitation to improvise new attachment points.

Check Reference / action
Scope OverNOut SM, US SKU 8007444
Minimum crossbar spread 24 in / 609.6 mm
Deployed canopy 54 × 78 in / 1371.6 × 1981.2 mm
Bar-space description 6 in / 152.4 mm; check hardware too
Listed weight 22.75 lb; add to the roof-load calculation

3. Reserve bar width and case access

Yakima describes the attachment as using six inches of bar space. Sketch the available section of each bar with the neighbouring cargo box, bicycle carrier or boat mount in its actual position. Include the clamps underneath, not just the top-facing footprint. Check whether a tower, bar end or adjacent bracket interferes with installation. A paper outline can identify an obvious clash before lifting the awning, but final compatibility requires the approved hardware and installation checks.

4. Plot the open canopy and campsite movement

Mark the stated 54 × 78-inch canopy rectangle on an unobstructed surface as a planning exercise. That rectangle represents the canopy dimensions; it is not the complete campsite boundary. The legs, guy lines, stakes and movement around the setup also occupy space. Check the manual’s support and anchoring arrangement before deciding that a narrow parking pitch is sufficient. Consider where doors open and where people step out. Do not treat a bare canopy outline as a clear pedestrian route.

5. Check the packed travelling arrangement

The product page describes a 4.5-foot-long packed case and a 22.75 lb awning weight. Include the real packed assembly when assessing roof load, garage clearance and nearby hatch or door movement. Measure from level ground after the permitted installation is complete. Repeat the check when other roof cargo changes. A close fit beside a box may also leave poor access to a zipper or fastening, so practise the normal opening and packing operation while safely parked before committing to the arrangement.

Before you decide

  • Identify the size and download its manual.
  • Confirm approved bar spread and clamp compatibility.
  • Plan canopy, legs, guy lines and access together.
  • Measure packed height and check the complete roof load.

FAQ

Does a 54 × 78-inch patch guarantee enough campsite space?

No. It covers the stated canopy dimensions. Supports, anchoring and people need additional usable space.

Does universal mounting mean every roof rack works?

No. Check the particular bar profile, spread, attachment position and rack and vehicle limits.

Official sources and scope

Checked on 23 October 2026. These references apply to the identified product, version and region. Follow its matching current instructions. Any worked measurement example is hypothetical.