Result — Conditional. A 120mm fan’s face size does not establish its installed thickness. Noctua lists the NF-A12x15 PWM at 15 mm without its pads and 16 mm with them, while the NF-A12x25 G2 PWM is 25 mm bare and 27 mm with pads. A slim slot must accept the complete intended assembly and its approved fasteners.

1. Identify the exact 120mm fan model
Read the full model name, revision and connector variant. This comparison uses the NF-A12x15 PWM and the NF-A12x25 G2 PWM, rather than every product with A12 in its name. Their shared nominal face size is useful for finding candidate mounting positions, but it does not define depth, accessory compatibility or the permitted mounting method. Keep the case, cooler or radiator identification alongside the fan model so the assembly instructions can be checked together.
2. Dimensions: include the anti-vibration pads
The current specification pages distinguish measurements with and without pads. Both compared fans have a 120 × 120 mm face and 105 × 105 mm mounting-hole spacing, but the padded thicknesses differ: 16 mm for the slim model and 27 mm for the G2 model. Use the assembly state that you actually intend to install. A hypothetical 20 mm clear space is 4 mm greater than the slim padded thickness but 7 mm less than the G2 padded thickness. That calculation does not establish the necessary operating clearance.
| Current Noctua specification | NF-A12x15 PWM | NF-A12x25 G2 PWM |
|---|---|---|
| Bare dimensions | 120 × 120 × 15 mm | 120 × 120 × 25 mm |
| With anti-vibration pads | 120 × 120 × 16 mm | 120 × 120 × 27 mm |
| Mounting-hole spacing | 105 × 105 mm | 105 × 105 mm |
| Rated voltage / connection | 12 V / four-pin | 12 V / four-pin |
3. Measure the real obstruction behind the mounting plane
Measure from the intended fan mounting plane to the closest obstacle across the whole footprint. A cable connector, memory module, motherboard component, panel rib or radiator fitting may be closer than the broad flat surface behind it. Check the insertion path as well as the final position. A cardboard outline can identify a geometric clash while the equipment is safely disconnected, but remove all temporary material before operation. Do not let a cable enter the blade area to recover space.
4. Match fasteners and accessories to the new thickness
Changing fan thickness can change the required fastener or clip arrangement. Do not assume the screws used through a 25 mm fan are appropriate through a 15 mm fan, especially into a radiator or a threaded component behind it. Use the hardware dimensions and engagement specified by the fan and mounting-product manufacturers. The difference in bare fan thickness is 10 mm; that is not an instruction to cut a particular screw by 10 mm. Gaskets, grills and spacers also add their own installed thickness.
5. Check the electrical and airflow arrangement
Both cited PWM variants list a four-pin connection and 12 V rating, but physical installation still needs the intended compatible fan-header and control arrangement. Follow the equipment’s connection and current-limit instructions rather than choosing by plug appearance alone. Verify orientation, cable routing and clear blade movement before following the normal start-up procedure. A fan that fits geometrically is not automatically an equivalent cooling solution: different fan designs and the surrounding restriction can change performance, so reassess the complete cooling arrangement after a replacement.
Before you decide
- Identify the exact fan and mounting product.
- Compare the complete padded thickness with the real cavity.
- Check insertion, cables, grills and other accessories.
- Use the specified fasteners and connection arrangement.
FAQ
Do matching 105 mm mounting holes prove that both fans fit?
No. They describe the screw pattern, not depth, insertion clearance or surrounding obstacles.
Can I reuse radiator screws just because they thread in?
Use the radiator and fan manufacturers’ specified hardware and engagement. A different fan thickness changes how far a screw can project behind it.
Official sources and scope
Checked on 23 October 2026. These references apply to the identified product, version and region. Follow its matching current instructions. Any worked measurement example is hypothetical.



