SAMLA 17-Gallon Fit is a useful closet check because the bare box and box-with-lid listings do not have the same published width. Planning from the smaller measurement can produce a shelf arrangement that stops working once lids are added. This guide covers IKEA’s clear box-with-lid combination 994.407.74 and distinguishes it from the bare box and clip-lock combinations.
SAMLA 17-Gallon Fit: the quick verdict
Use the dimensions of the exact assembled combination you will store. Then verify the opening, shelf support, hand access and removal path. A bin can fit inside a compartment yet be difficult to take out. All worked examples here are hypothetical geometry checks, not firsthand tests or prescribed handling clearances.

| Item | Published dimensions or example |
|---|---|
| Box with lid, 994.407.74 | 22½ × 15¼ × 16½ inches |
| Bare box, 001.029.75 | 22 × 15¼ × 16½ inches |
| Hypothetical clear shelf opening | 23 wide × 16 deep × 17 high inches |
| Difference with lidded box | ½ wide × ¾ deep × ½ high inches total |
1. Match the complete combination
Start with the full product name and article number. Do not substitute a photo of a similar SAMLA size or assume a separately purchased lid leaves the external envelope unchanged. Accessories and different combinations can change the widest or highest point that must pass through the opening.
The listed width difference between the bare box and this lidded combination is ½ inch. That small difference matters for SAMLA 17-Gallon Fit in a tight compartment. Measure an existing sample with its lid fully fitted if you are buying more containers to match a shelf already in use.
2. Measure the actual opening, not the shelf label
A closet shelf described as 24 inches wide may have less usable space between brackets, side panels or a door frame. Measure the narrowest opening along the complete insertion route. Include a shelf’s front lip and any hinge that protrudes into the path.
In the hypothetical 23-by-16-by-17-inch opening, the lidded bin leaves only ½ inch total width, ¾ inch depth and ½ inch height. Those numbers describe dimensional differences. They do not include your fingers, slight shelf sag, an uneven lid or room to angle the container during removal.
3. Separate storage fit from hand access
Consider how you will grip the box when it is full. If both sides sit close to compartment walls, a grip that works on the floor may be unavailable on the shelf. Check whether the shelf edge blocks access to the rim or forces you to pull on the lid.
A practical SAMLA 17-Gallon Fit trial uses an actual box or a rigid mock-up of the full envelope. Start empty, confirm the movement, and assess the loaded handling task separately. Do not assume that a box pushed into position can be retrieved comfortably once its contents add weight.
4. Check shelf depth, support and weight
Compare the complete box position with the shelf’s supported area. A closet door or rear obstruction may prevent the bin from sitting where the plan suggests. If you rotate the container, its wider dimension becomes the required depth, so repeat every measurement instead of treating rotation as a free solution.
The 17-gallon capacity is a volume label, not a shelf-load allowance. Books, craft supplies and bedding create very different weights in the same box. Check the shelf system’s rated load and installation instructions, including how its supports carry the load. Do not infer structural safety from the bin’s size or material.
5. Plan opening, stacking and the room beyond
Decide whether the lid will be removed while the box is on the shelf or only after taking it down. The former requires space for hands and the lid’s movement. The latter requires a suitable landing place and an unobstructed route out of the closet.
For stacked storage, measure the assembled stack directly rather than multiplying height and assuming the nesting geometry. Finish SAMLA 17-Gallon Fit by checking closet-door travel, nearby furniture and your ability to identify and retrieve the intended container without disturbing unstable objects.
Before-you-buy checklist
- Match the lidded combination and article number.
- Measure the narrowest insertion opening in three dimensions.
- Check fingers, rim access and the full removal movement.
- Verify shelf support and the intended loaded weight.
- Plan where the bin and lid go during retrieval.
FAQ
Will it fit a 22-inch-wide compartment?
The listed lidded width is 22½ inches, so that orientation fails the published-width comparison. The bare-box listing cannot approve the lidded combination.
Are the dimensions the usable interior?
No. Use them for the outside envelope. Measure the interior and opening separately for rigid objects you want to store inside.
What confirms SAMLA 17-Gallon Fit?
The assembled bin must pass through the opening, sit on a suitable shelf and come back out with a practical grip. Check all three before buying a set.
Related fit guides
See storage bins in IKEA KALLAX for another outside-versus-opening comparison, and IVAR shelf-depth fit when choosing shelving.
Official sources
Checked November 5, 2026: IKEA’s SAMLA box-with-lid listing and bare SAMLA box listing. Recheck the exact combination before purchase.



